Ibm RS/6000 Manual de usuario Pagina 50
- Pagina / 228
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
PCI SCSI-2 Differential Fast/Wide Adapter
The adapter can burst data to devices on the SCSI bus at 20 MB/sec.
It has a single connector for attachment of external differential devices. It is a
shielded 68-conductor connector consisting of two rows of 34 female contacts.
Both 8-bit and 16-bit device attachments are supported, but intermixing 8-bit and
16-bit devices is not supported.
The maximum number of addressable IDs enabled by the adapter is 15, but due to
cabling restrictions, the actual total number of supported devices attached to the
internal and external connector may be less.
The adapter occupies one PCI bus slot, and a maximum of six adapters can be
installed in the Model E20.
The following table shows the maximum number of both internal and external
devices that can be attached to a SCSI-2 adapter together with related cables. By
“Multi-device,” we mean an external enclosure that may contain more than one
SCSI device.
Table 6. SCSI Adapter Connections on Model E20
Adapter Maximum number of devices Cables Feature Code
Feature
Code
Internal External Internal External
Single MultiDevice
Native 7 0 0 Not
required
Not
allowed
2408 4 4 0 2442 2111,
2113,
2115, 2117
2408 0 4 0 Not
allowed
2111,
2113,
2115, 2117
2408 0 0 1 Not
allowed
2111,
2113,
2115, 2117
2409 0 25 meter cable maximum Not
allowed
2112,
2114, 2116
Note: Maximum SCSI adapters: 6
2.4.2.6 Communication Adapters
The following communication adapters are supported:
Auto LANstreamer Token-Ring PCI Adapter
PCI Ethernet Adapters
ISA X.25 Adapter
ISA 4-Port Multiprotocol Communications Controller
ISA 8-Port Asynchronous Controller EIA-232
ISA 128-Port Asynchronous Controller
26 Introduction to PCI-Based RS/6000 Servers
- April 1996 1
- First Edition (April 1996) 4
- Abstract 5
- Contents 7
- Special Notices 17
- Platform (CHRP) 19
- Related Publications 20
- Preface xix 21
- Acknowledgments 23
- Chapter 1. Introduction 25
- Chapter 1. Introduction 3 27
- Chapter 1. Introduction 5 29
- 1.3.3 PowerPC Platform Goals 31
- 1.3.4 CHRP Certification 32
- Architecture 33
- 2.1 The Hardware Design 35
- High Data Transfer Speed 37
- Processor Independence 37
- Cross-Platform Compatibility 37
- Multi-bus Support 38
- Plug and Play 38
- Investment protection 38
- 2.2.1 The Processor Subsystem 39
- 2.2.2 The L2 Cache 40
- 2.2.5 The Primary PCI Bus 41
- 2.2.4 The System Memory 41
- 2.2.6 The Secondary PCI Bus 42
- 2.2.7 The EISA Bus 42
- 2.2.8 The X-Bus 42
- 2.3 Electronics Partitioning 43
- 2.4.1 Standard Features 45
- Integrated SCSI-2 adapter 46
- Standard I/O ports 46
- 2.4.2.1 Internal Disk Drives 47
- 2.4.2.2 Internal Tape Drives 47
- 2.4.2.4 Graphics Adapter 48
- 2.4.2.5 PCI SCSI-2 Adapters 49
- PCI Ethernet Adapters 51
- 2.4.2.7 External Subsystems 54
- Internal Disk Drives 55
- Internal Tape Drives 55
- Graphics Adapter 55
- SCSI Adapters 55
- 2.5.1 Standard Features 56
- Integrated SCSI-2 Adapter 57
- 2.5.2.1 Internal Disk Drives 58
- 2.5.2.2 Internal Tape Drives 59
- 2.5.2.4 Graphics Adapter 59
- 2.5.2.5 PCI SCSI-2 Adapters 60
- 2.5.2.7 External Subsystems 61
- 2.6 Hardware Requirements 62
- 2.7 Performance Positioning 62
- SPEC base metrics 64
- SPEC rate metrics 64
- Chapter 3. Hot-Swap Subsystem 65
- 3.1.1 Backplanes 66
- 3.1.2 Hot-Swap Bays and Banks 67
- 3.2 Installation 68
- 3.2.5 Disk Carriers 70
- 3.3.4 Mirroring 74
- Managing 77
- 4.1 Boot Record 78
- 4.2.1 Firmware 80
- 4.2.2 Software ROS for AIX 80
- 4.3 Boot Image 82
- Name Description 83
- Base Proto Files: 84
- Proto Extension Files: 84
- 4.3.1.2 RAM File System 85
- Master Partition Header 86
- Reserved 1 86
- Reserved 2 86
- 4.4.1 Firmware Boot Sequence 89
- 4.4.2 Firmware Passwords 91
- 4.4.3 Firmware Flash Update 92
- 4.4.4 Firmware Recovery 93
- 4.4.5.3 Graphics Adapter POST 94
- 4.4.5.5 SCSI Subsystem POST 94
- 4.5 LCD Panel 95
- 4.6.1 SMS Graphical Main Menu 97
- 4.6.2 SMS ASCII Main Menu 97
- 4.6.3 Start-Up Menu 97
- 4.6.4 Test Menu 98
- 4.6.5 Tools Menu 98
- 5.1.1 Boot-Device Order List 99
- 5.1.3 bootlist Command 102
- 5.2 Entering Debug Mode 102
- 5.3 System Dump Support 103
- 5.3.4 Dump LCD Support 106
- 5.4 Managing System Backups 106
- 5.4.1 The bootinfo Command 107
- 5.4.6 Cloning 112
- 5.5 Configuration Information 114
- 5.6 Graphics Support 116
- 5.6.2 Resolution 118
- 5.6.3 Configuring the Adapter 118
- DISPLAY Variable Description 121
- RS/6000 Servers 123
- SG24-2581-00 124
- 6.1.2 Device Location Codes 125
- 6.2 PCI Adapter Configuration 126
- 6.3 ISA Adapter Configuration 128
- Figure 35. SMIT ISA Menu 131
- 6.4.1 DIP-Switch Setting 132
- 6.4.2 Configuring the Adapter 133
- 6.5.1 DIP-Switch Setting 136
- 6.5.2 Configuring the Adapter 136
- 6.6.2 DIP-Switch Setting 140
- 6.6.3 Configuring the Adapter 141
- Interrupt Level 142
- Bus I/O Address 142
- Bus Memory 142
- 6.7.1 DIP-Switch Setting 145
- 6.7.2 Configuring the Adapter 146
- System User's Guide 153
- Firmware Level 158
- Chapter 7. SCSI Cabling 161
- 7.1.2 SCSI Terminators 162
- 7.1.3 SCSI Device Addresses 162
- 7.1.4 SCSI Bus Width 162
- 8.2 Stand-Alone Diagnostics 172
- 8.3 Online Diagnostics 176
- 8.3.1 Concurrent Mode 176
- 8.3.2 Service Mode 177
- 8.3.3 Maintenance Mode 178
- Machine Object Name 179
- Operation to Perform 179
- Enable Diagnostics Boot 179
- 9.1 NIM Concepts 181
- 9.1.1 NIM Environment 181
- 9.1.2 NIM Objects 182
- 9.1.2.2 Network Objects 183
- 9.1.2.3 Machine Objects 183
- Network Install Route 184
- Gateway1 184
- Gateway2 184
- Network2 184
- 9.2.1 NIM Master Requirements 185
- 9.2.2 Filesystem Creation 185
- 9.2.3 NIM Master Activation 186
- Standalone1 187
- /inst.images 193
- Resource Object 194
- Chapter 10. Troubleshooting 203
- 10.2 Booting Problems 204
- 10.2.1 Booting From CD-ROM 204
- From this shell, you can 205
- 10.3 Installation Problems 206
- 10.3.2 NIM Installation 206
- 10.6.2.1 Power-On Password 208
- Figure 55. Operator Panel 210
- Table 35. LED Functions 210
- List of Abbreviations 219
- (continued) 223
- (continued) 223
- Name Address 225
- Company or Organization 225
- Phone No 225
- BUSINESS REPLY MAIL 226
- Printed in U.S.A 228
- SG24-469- 228
Relacionado con productos y manuales para Ordenadores Ibm RS/6000
Ordenadores Ibm 6644 Manual de usuario
(100 paginas)
(100 paginas)
Ordenadores Ibm 1483DSV Manual de usuario
(141 paginas)
(141 paginas)
Ordenadores Ibm 47AE - 410168 Manual de usuario
(27 paginas)
(27 paginas)
Ordenadores Ibm 4190 Manual de usuario
(84 paginas)
(84 paginas)
Ordenadores Ibm GC09-2830-00 Manual de usuario
(196 paginas)
(196 paginas)
Ordenadores Ibm Novell 10 SP1 EAL4 Manual de usuario
(246 paginas)
(246 paginas)
Ordenadores Ibm A40 TYPE 6840 Manual de usuario
(148 paginas)
(148 paginas)
Ordenadores Ibm NETVISTA 6824 Manual de usuario
(60 paginas)
(60 paginas)
Ordenadores Ibm 440 Manual de usuario
(202 paginas)
(202 paginas)
Ordenadores Ibm GC23-7753-05 Manual de usuario
(56 paginas)
(56 paginas)
Ordenadores Ibm 610 Manual de usuario
(40 paginas)
(40 paginas)
Ordenadores Ibm NETVISTA X40 6643 Manual de usuario
(120 paginas)
(120 paginas)
Ordenadores Ibm POWER 730 Manual de usuario
(45 paginas)
(45 paginas)
Ordenadores Ibm 6648 Manual de usuario
(248 paginas)
(248 paginas)
Ordenadores Ibm 755 Manual de usuario
(47 paginas)
(47 paginas)
Ordenadores Ibm 170 Manual de usuario
(18 paginas)
(18 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.060 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales