Ibm RS/6000 Manual de usuario Pagina 216
- Pagina / 228
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Table 36 (Page 4 of 5). Firmware Checkpoint Three-Digit Codes
Code Description
FAB Keyboard driver initialization
FAC Keyboard driver exit
FAD Mouse driver initialization
FAE Mouse driver exit
FB0 Initialize rest of file system
FB1 Diskette initialization
FB2 Diskette drive type determination
FB3 Diskette initialization complete
FC0 Check if flash ROM OK
FCA Build boot table - Networks
FCB Build boot table - DASD
FCC Build boot table - CD ROM
FCD Build boot table - diskettes
FCE No Operating System boot, exit normal boot sequence
FD0 Start of boot sequence
FD2 No Operating System boot - ensure CMOS RTC periodic clock updates
displayed
FD4 Initialize console for loading diagnostics
FD8 Exit from diagnostic - run resident monitor
FDA IRQ 15
FDB Unexpected processor exception
FDC Unexpected external interrupt exception
FDD Early processor exception
FDE Shutdown entire file system
FE1 Test Timeout
FE2 Initialize System I/O
FE4 Initialize Super I/O with default values
FE6 Set up early memory allocation heap
FE8 Initialize primary diskette drive in polled mode
FEA Try to load in recovery image from diskette
FEB Verify recovery image is valid
FEC Get recovery image entry point
FED Invalidate instruction cache
FEE Jump to composite image
FF0 Manufacturing - Check for Parallel Port hook
FF4 Manufacturing - Start flag not received
FF5 Manufacturing - Invalid Start flag received
FF6 Manufacturing - Receive character timeout
FF7 Manufacturing - CRC value mismatch
192 Introduction to PCI-Based RS/6000 Servers
- April 1996 1
- First Edition (April 1996) 4
- Abstract 5
- Contents 7
- Special Notices 17
- Platform (CHRP) 19
- Related Publications 20
- Preface xix 21
- Acknowledgments 23
- Chapter 1. Introduction 25
- Chapter 1. Introduction 3 27
- Chapter 1. Introduction 5 29
- 1.3.3 PowerPC Platform Goals 31
- 1.3.4 CHRP Certification 32
- Architecture 33
- 2.1 The Hardware Design 35
- High Data Transfer Speed 37
- Processor Independence 37
- Cross-Platform Compatibility 37
- Multi-bus Support 38
- Plug and Play 38
- Investment protection 38
- 2.2.1 The Processor Subsystem 39
- 2.2.2 The L2 Cache 40
- 2.2.5 The Primary PCI Bus 41
- 2.2.4 The System Memory 41
- 2.2.6 The Secondary PCI Bus 42
- 2.2.7 The EISA Bus 42
- 2.2.8 The X-Bus 42
- 2.3 Electronics Partitioning 43
- 2.4.1 Standard Features 45
- Integrated SCSI-2 adapter 46
- Standard I/O ports 46
- 2.4.2.1 Internal Disk Drives 47
- 2.4.2.2 Internal Tape Drives 47
- 2.4.2.4 Graphics Adapter 48
- 2.4.2.5 PCI SCSI-2 Adapters 49
- PCI Ethernet Adapters 51
- 2.4.2.7 External Subsystems 54
- Internal Disk Drives 55
- Internal Tape Drives 55
- Graphics Adapter 55
- SCSI Adapters 55
- 2.5.1 Standard Features 56
- Integrated SCSI-2 Adapter 57
- 2.5.2.1 Internal Disk Drives 58
- 2.5.2.2 Internal Tape Drives 59
- 2.5.2.4 Graphics Adapter 59
- 2.5.2.5 PCI SCSI-2 Adapters 60
- 2.5.2.7 External Subsystems 61
- 2.6 Hardware Requirements 62
- 2.7 Performance Positioning 62
- SPEC base metrics 64
- SPEC rate metrics 64
- Chapter 3. Hot-Swap Subsystem 65
- 3.1.1 Backplanes 66
- 3.1.2 Hot-Swap Bays and Banks 67
- 3.2 Installation 68
- 3.2.5 Disk Carriers 70
- 3.3.4 Mirroring 74
- Managing 77
- 4.1 Boot Record 78
- 4.2.1 Firmware 80
- 4.2.2 Software ROS for AIX 80
- 4.3 Boot Image 82
- Name Description 83
- Base Proto Files: 84
- Proto Extension Files: 84
- 4.3.1.2 RAM File System 85
- Master Partition Header 86
- Reserved 1 86
- Reserved 2 86
- 4.4.1 Firmware Boot Sequence 89
- 4.4.2 Firmware Passwords 91
- 4.4.3 Firmware Flash Update 92
- 4.4.4 Firmware Recovery 93
- 4.4.5.3 Graphics Adapter POST 94
- 4.4.5.5 SCSI Subsystem POST 94
- 4.5 LCD Panel 95
- 4.6.1 SMS Graphical Main Menu 97
- 4.6.2 SMS ASCII Main Menu 97
- 4.6.3 Start-Up Menu 97
- 4.6.4 Test Menu 98
- 4.6.5 Tools Menu 98
- 5.1.1 Boot-Device Order List 99
- 5.1.3 bootlist Command 102
- 5.2 Entering Debug Mode 102
- 5.3 System Dump Support 103
- 5.3.4 Dump LCD Support 106
- 5.4 Managing System Backups 106
- 5.4.1 The bootinfo Command 107
- 5.4.6 Cloning 112
- 5.5 Configuration Information 114
- 5.6 Graphics Support 116
- 5.6.2 Resolution 118
- 5.6.3 Configuring the Adapter 118
- DISPLAY Variable Description 121
- RS/6000 Servers 123
- SG24-2581-00 124
- 6.1.2 Device Location Codes 125
- 6.2 PCI Adapter Configuration 126
- 6.3 ISA Adapter Configuration 128
- Figure 35. SMIT ISA Menu 131
- 6.4.1 DIP-Switch Setting 132
- 6.4.2 Configuring the Adapter 133
- 6.5.1 DIP-Switch Setting 136
- 6.5.2 Configuring the Adapter 136
- 6.6.2 DIP-Switch Setting 140
- 6.6.3 Configuring the Adapter 141
- Interrupt Level 142
- Bus I/O Address 142
- Bus Memory 142
- 6.7.1 DIP-Switch Setting 145
- 6.7.2 Configuring the Adapter 146
- System User's Guide 153
- Firmware Level 158
- Chapter 7. SCSI Cabling 161
- 7.1.2 SCSI Terminators 162
- 7.1.3 SCSI Device Addresses 162
- 7.1.4 SCSI Bus Width 162
- 8.2 Stand-Alone Diagnostics 172
- 8.3 Online Diagnostics 176
- 8.3.1 Concurrent Mode 176
- 8.3.2 Service Mode 177
- 8.3.3 Maintenance Mode 178
- Machine Object Name 179
- Operation to Perform 179
- Enable Diagnostics Boot 179
- 9.1 NIM Concepts 181
- 9.1.1 NIM Environment 181
- 9.1.2 NIM Objects 182
- 9.1.2.2 Network Objects 183
- 9.1.2.3 Machine Objects 183
- Network Install Route 184
- Gateway1 184
- Gateway2 184
- Network2 184
- 9.2.1 NIM Master Requirements 185
- 9.2.2 Filesystem Creation 185
- 9.2.3 NIM Master Activation 186
- Standalone1 187
- /inst.images 193
- Resource Object 194
- Chapter 10. Troubleshooting 203
- 10.2 Booting Problems 204
- 10.2.1 Booting From CD-ROM 204
- From this shell, you can 205
- 10.3 Installation Problems 206
- 10.3.2 NIM Installation 206
- 10.6.2.1 Power-On Password 208
- Figure 55. Operator Panel 210
- Table 35. LED Functions 210
- List of Abbreviations 219
- (continued) 223
- (continued) 223
- Name Address 225
- Company or Organization 225
- Phone No 225
- BUSINESS REPLY MAIL 226
- Printed in U.S.A 228
- SG24-469- 228
Relacionado con productos y manuales para Ordenadores Ibm RS/6000
Ordenadores Ibm 6644 Manual de usuario
(100 paginas)
(100 paginas)
Ordenadores Ibm 1483DSV Manual de usuario
(141 paginas)
(141 paginas)
Ordenadores Ibm 47AE - 410168 Manual de usuario
(27 paginas)
(27 paginas)
Ordenadores Ibm 4190 Manual de usuario
(84 paginas)
(84 paginas)
Ordenadores Ibm GC09-2830-00 Manual de usuario
(196 paginas)
(196 paginas)
Ordenadores Ibm Novell 10 SP1 EAL4 Manual de usuario
(246 paginas)
(246 paginas)
Ordenadores Ibm A40 TYPE 6840 Manual de usuario
(148 paginas)
(148 paginas)
Ordenadores Ibm NETVISTA 6824 Manual de usuario
(60 paginas)
(60 paginas)
Ordenadores Ibm 440 Manual de usuario
(202 paginas)
(202 paginas)
Ordenadores Ibm GC23-7753-05 Manual de usuario
(56 paginas)
(56 paginas)
Ordenadores Ibm 610 Manual de usuario
(40 paginas)
(40 paginas)
Ordenadores Ibm NETVISTA X40 6643 Manual de usuario
(120 paginas)
(120 paginas)
Ordenadores Ibm POWER 730 Manual de usuario
(45 paginas)
(45 paginas)
Ordenadores Ibm 6648 Manual de usuario
(248 paginas)
(248 paginas)
Ordenadores Ibm 755 Manual de usuario
(47 paginas)
(47 paginas)
Ordenadores Ibm 170 Manual de usuario
(18 paginas)
(18 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.090 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales