Ibm uPD78082 Manual de usuario Pagina 171
- Pagina / 274
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
148
CHAPTER 11 SERIAL INTERFACE CHANNEL 2
11.4 Serial Interface Channel 2 Operation
Serial interface channel 2 has the following three modes.
• Operation stop mode
• Asynchronous serial interface (UART) mode
• 3-wire serial I/O mode
11.4.1 Operation stop mode
In the operation stop mode, serial transfer is not performed, and therefore power consumption can be reduced.
In the operation stop mode, the P70/SI2/RxD, P71/SO2/TxD and P72/SCK2/ASCK pins can be used as normal
input/output ports.
(1) Register setting
Operation stop mode settings are performed using serial operating mode register 2 (CSIM2) and the
asynchronous serial interface mode register (ASIM).
(a) Serial operating mode register 2 (CSIM2)
CSIM2 is set with a 1-bit or 8-bit memory manipulation instruction.
RESET input sets CSIM2 to 00H.
CSIM
22
65432107
Symbol
CSIM2 CSIE2 0 0 0 0 CSCK 0
FF72H 00H R/W
Address After Reset R/W
CSIE2
0
1
Operation Control in 3-wire Serial I/O Mode
Operation stopped
Operation enabled
Caution Set 0 to the bits 0 and 3 to 6.
- PD78083 1
- SUBSERIES 1
- NOTES FOR CMOS DEVICES 2
- M7 96.5 4
- Regional Information 5
- Other Documents 11
- FIGURE (1/4) 17
- FIGURE (2/4) 18
- FIGURE (3/4) 19
- FIGURE (4/4) 20
- TABLE (1/2) 21
- TABLE (2/2) 22
- CHAPTER 1 OUTLINE 24
- 1.1 Features 24
- 1.2 Applications 25
- 1.3 Ordering Information 25
- 1.4 Quality Grade 26
- DD pin to VDD 27
- SS pin to VSS 27
- SS directly 28
- Pin Identifications 29
- SS via a pull-down resistor 30
- SS : Connect to the ground 30
- DD : Power Supply 31
- PP : Programming Power Supply 31
- SS : Ground 31
- 1.6 78K/0 Series Development 32
- Note 10 bits timer: 1 channel 33
- 1.7 Block Diagram 34
- DD = 1.8 to 5.5 V 35
- A = –40 to +85°C 35
- PD78081(A), 78082(A) and 36
- 78P083(A), and the 36
- PD78081(A2) 36
- CHAPTER 1 OUTLINE 37
- CHAPTER 2 PIN FUNCTION 38
- 2.1 Pin Function List 38
- (2) Pins other than port pins 39
- PD78P083 only) 39
- CHAPTER 2 PIN FUNCTION 40
- As short as possible 44
- CHAPTER 3 CPU ARCHITECTURE 48
- 3.1 Memory Spaces 48
- Figure 3-2. Memory Map ( 49
- PD78082) 49
- Figure 3-3. Memory Map ( 50
- PD78P083) 50
- CHAPTER 3 CPU ARCHITECTURE 52
- PD78081) 53
- IE Z RBS1 AC RBS0 0 ISP CY 56
- PD78081 : 82H 62
- PD78082 : 64H 62
- PD78P083 : 46H 62
- Identifier Description 68
- [Illustration] 72
- — [HL + byte] 74
- — [HL + B], [HL + C] 75
- CHAPTER 4 PORT FUNCTIONS 76
- 4.1 Port Functions 76
- Table 4-1. Port Functions 77
- 4.2 Port Configuration 78
- Internal bus 80
- PM : Port mode register 84
- RD : Port 7 read signal 84
- WR : Port 7 write signal 84
- CHAPTER 4 PORT FUNCTIONS 86
- Input/Output 87
- 4.4 Port Function Operations 90
- CHAPTER 5 CLOCK GENERATOR 92
- CHAPTER 5 CLOCK GENERATOR 94
- 5.4 System Clock Oscillator 96
- (c) Signals are fetched 98
- 5.4.2 Scaler 98
- X) is secured automatically 101
- PM101 : Bit 1 of PM10 106
- 2. n = 5, 6 106
- X = 5.0 MHz 108
- X or fX/2) 109
- Remark n = 5, 6 120
- CHAPTER 7 WATCHDOG TIMER 126
- 7.1 Watchdog Timer Functions 126
- CHAPTER 7 WATCHDOG TIMER 127
- Selector 128
- PCL/P35 Pin Output 134
- CHAPTER 10 A/D CONVERTER 142
- 10.1 A/D Converter Functions 142
- CHAPTER 10 A/D CONVERTER 143
- Tap Selector 143
- REF = VDD 154
- REF and ANI0 to ANI7. Since 155
- REF pin input impedance 155
- REF pin and the AVSS pin 155
- RESET input sets ASIM to 00H 172
- ParityRxD Pin 185
- <3><1> 185
- <2> 185
- WDT : Watchdog timer 205
- CPU: CPU clock) 207
- 1 Instruction 212
- Execution 212
- CHAPTER 13 STANDBY FUNCTION 216
- 13.2.1 HALT mode 218
- Oscillation 220
- DD via a pull-up resistor 221
- CHAPTER 14 RESET FUNCTION 224
- 14.1 Reset Function 224
- CHAPTER 14 RESET FUNCTION 226
- CHAPTER 15 228
- PD78P083 228
- 15.2 PROM Programming 230
- DD = 6.5 V, VPP = 12.5 V 232
- DD = 4.5 to 5.5 V, VPP = VDD 232
- DD and VPP pins 236
- CHAPTER 16 INSTRUCTION SET 238
- CHAPTER 16 INSTRUCTION SET 239
- 16.2 Operation List 241
- Note 1 Note 2 243
- (1) 8-bit instructions 249
- [HL + B] $addr16 250
- [HL + C] 250
- APPENDIX A DEVELOPMENT TOOLS 254
- A.2 PROM Programming Tools 257
- A.3 Debugging Tools 258
- A.3.2 Software (1/3) 259
- S××××SM78K0 259
- A.3.2 Software (2/3) 260
- S××××ID78K0 260
- A.4 OS for IBM PC 262
- Based on EV-9200G-44 264
- (1) Package drawing (in mm) 264
- (2) Pad drawing (in mm) 265
- B.1 Real-time OS 267
- APPENDIX C REGISTER INDEX 270
- C.1 Register Index 270
- APPENDIX C REGISTER INDEX 271
- DD = 1.8 to 5.5V 272
- Facsimile 274
Relacionado con productos y manuales para Hardware Ibm uPD78082
Hardware Ibm 22P6415 Manual de usuario
(62 paginas)
(62 paginas)
Hardware Ibm HOTS Manual de usuario
(13 paginas)
(13 paginas)
Hardware Ibm THINKPAD 72 W DC Manual de usuario
(70 paginas)
(70 paginas)
Hardware Ibm 20X Manual de usuario
(17 paginas)
(17 paginas)
Hardware Ibm ThinkPad 73P3292 Manual de usuario
(52 paginas)
(52 paginas)
Hardware Ibm RELEASE 7.3 Manual de usuario
(388 paginas)
(388 paginas)
Hardware Ibm 100/10 Manual de usuario
(162 paginas)
(162 paginas)
Hardware Ibm 10K3791 Manual de usuario
(5 paginas)
(5 paginas)
Hardware Ibm N7000 Manual de usuario
(8 paginas)
(8 paginas)
Hardware Ibm DS8000 Manual de usuario
(450 paginas)
(450 paginas)
Hardware Ibm THINKPAD 600 Manual de usuario
(18 paginas)
(18 paginas)
Hardware Ibm 31P8128 Manual de usuario
(112 paginas)
(112 paginas)
Hardware Ibm 27L2579 Manual de usuario
(20 paginas)
(20 paginas)
Hardware Ibm 51 Manual de usuario
(248 paginas)
(248 paginas)
Hardware Ibm DR550 Manual de usuario
(128 paginas)
(128 paginas)
Hardware Ibm 22P7035 Manual de usuario
(54 paginas)
(54 paginas)
Hardware Ibm SYSTEM STORAGE DS4300 Manual de usuario
(11 paginas)
(11 paginas)
Hardware Ibm THINKCENTRE 8123 Manual de usuario
(44 paginas)
(44 paginas)
Hardware Ibm THINKCENTER 8189 Manual de usuario
(290 paginas)
(290 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.158 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales