IBM Security Camera 343 Manual de usuario Pagina 140
- Pagina / 187
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
128 xSeries 343 Hardware Maintenance Manual
The guide consists of a series of steps presented in a checklist. Begin the checks with the power
off, and the power cord disconnected.
Checklist:
1. Check exterior covers for damage (loose, broken, or sharp edges).
2. Power-off the computer. Disconnect the power cord.
Check the power cord for:
a. A third-wire ground connector in good condition. Use a meter to measure third-wire
ground continuity for 0.1 ohm or less between the external ground pin and frame ground.
b. The power cord should be the appropriate type as specified in the parts listings.
c. Insulation must not be frayed or worn.
3. Remove the cover.
4. Check for any obvious non-IBM alterations. Use good judgment as to the safety of any non-
IBM alterations.
5. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination,
water or other liquids, or signs of fire or smoke damage.
6. Check for worn, frayed, or pinched cables.
7. Check that the power-supply cover fasteners (screws or rivets) have not been removed or
tampered with.
Handling Electrostatic Discharge-sensitive Devices
Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive
to electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge
between objects. Protect against ESD damage by equalizing the charge so that the machine, the
part, the work mat, and the person handling the part are all at the same charge.
Notes
1. Use product-specific ESD procedures when they exceed the requirements noted here.
2. Make sure that the ESD protective devices you use have been certified (ISO 9000) as fully
effective.
When handling ESD-sensitive parts:
• Keep the parts in protective packages until they are inserted into the product.
• Avoid contact with other people.
• Wear a grounded wrist strap against your skin to eliminate static on your body.
• Prevent the part from touching your clothing. Most clothing is insulative and retains a charge
even when you are wearing a wrist strap.
• Use the black side of a grounded work mat to provide a static-free work surface. The mat is
especially useful when handling ESD-sensitive devices.
- Hardware Maintenance Manual 1
- Contents 3
- Contents v 5
- Figures 6
- Contents vii 7
- Contents ix 9
- CAUTION 10
- Part I: User’s Guide 13
- 1 Introduction 17
- Before You Begin 18
- 2 Chassis Description 19
- Features and Specifications 20
- Environmental Specifications 21
- Chassis Feature Location 22
- Back Panel 25
- Internal Chassis Features 26
- Processor 27
- PCI Riser Slots 27
- SCSI Controller 27
- Network Controller 28
- Network Teaming Features 28
- Keyboard and Mouse 29
- RJ45 Serial Port 30
- Security 31
- Riser Boards 34
- Power Supplies 35
- DC Power Subsystem 35
- Introduction 36
- Interface Requirements 36
- Peripheral Bay 37
- Hard Drive Tray 37
- Cooling Subsystem 38
- Server Management Summary 39
- Electronic Emission Notices 41
- Using BIOS Setup 46
- Setup Menus 47
- Main Menu 48
- Advanced Menu 49
- PCI Configuration Submenu 50
- USB Function Submenu 50
- Security Menu 51
- Server Menu 52
- Console Redirection Submenu 53
- Boot Menu 54
- Exit Menu 55
- Upgrading the BIOS 56
- Recovering the BIOS 58
- Changing the BIOS Language 59
- What You Need to Do 59
- Running the SSU from the CD 59
- Starting the SSU 60
- Customizing the SSU 61
- Launching a Task 62
- SEL Manager Add-in 62
- SDR Manager Add-in 63
- FRU Manager Add-in 63
- FRU/SDR Load Utility 64
- Parsing the Command Line 66
- Displaying Usage Information 66
- Displaying a Given Area 66
- Using Specified CFG File 67
- Updating the BMC Firmware 68
- Updating the FRU/SDR Files 69
- Running the SCSI Utility 69
- 5 Upgrading the Hardware 71
- 6 Upgrading the Chassis 71
- Equipment Rack Precautions 72
- Replacing Hard Disk Drives 76
- Working Inside the System 78
- To Connect: To Disconnect: 79
- Internal Chassis Layout 82
- Figure 16. Installing DIMMs 83
- Removing a Processor 88
- Upgrading the Chassis 85 97
- Upgrading the Chassis 87 99
- Replacing Fans 100
- Replacing a 40 mm Fan 101
- 7 Technical Reference 103
- Serial Ports 105
- Configuration Jumpers 106
- Figure 39 107
- Figure 40 107
- FRU List 108
- Technical Reference 97 109
- Failure Information 110
- Note: G=Green, R=Red 111
- POST Error Beep Codes 118
- PC Doctor Symtom to FRU 120
- Equipment Log 122
- Warnings 111 123
- C Solving Problems 124
- Solving Problems 113 125
- Monitoring POST 126
- Power Light Does Not Light 127
- Cannot Connect to a Server 129
- Problems with Network 129
- PCI Installation Tips 130
- Problem Determination Tips 131
- Getting Information 132
- Software Service and Support 133
- Hardware Service and Support 133
- E Safety Addendum 136
- Electrical Safety 137
- Safety Inspection Guide 139
- Grounding Requirements 141
- Statement 2 143
- Statement 3 143
- Safety Addendum 133 145
- Instrução 2 146
- Instrução 3 146
- Safety Addendum 135 147
- CUIDADO 148
- Safety Addendum 137 149
- Safety Addendum 139 151
- Safety Addendum 141 153
- Safety Addendum 143 155
- Safety Addendum 145 157
- Safety Addendum 147 159
- Notice n° 2 161
- Notice n° 3 161
- Safety Addendum 151 163
- Hinweis 2 164
- Hinweis 3 164
- Safety Addendum 153 165
- Avviso 2 167
- Avviso 3 167
- Safety Addendum 157 169
- Safety Addendum 159 171
- Safety Addendum 161 173
- Safety Addendum 163 175
- Declaración 2 177
- Declaración 3 177
- >82 kg 179
- F Product Notices 180
- Trademarks 181
- Important Notes 181
- Index 171 183
- Index 173 185
- Part Number: 59P2178 187
Precor TRM 800 manuals
Owner’s manuals and user’s guides for Sports and recreation Precor TRM 800.
We providing 1 pdf manuals Precor TRM 800 for download free by document types: User Manual
Comentarios a estos manuales