IBM RS/6000 Manual de usuario Pagina 247
- Pagina / 290
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
a. AT&F reset command, or
b. AT&Fn reset commands, where n can be 0, 1, etc.?
If AT&F, configuration file modem_f.cfg is recommended.
If AT&Fn, configuration file modem_f0.cfg or modem_f1.cfg is recommended,
depending on which provides the hardware flow control profile.
7. Selection is complete.
If your modem configuration selection is not available in the Service Processor
Modem Configuration Menu, you must access it through the Configure Remote
Maintenance Policy Service Aid.
If you find it necessary to adjust any of these configuration files, do so with refer-
ence to the manual that came with your modem. It is recommended you select
settings that enable hardware flow control and respond to DTR.
Note: Some older modems do not respond to the commands X0 or &R1. You
should edit out these commands from the modem configuration file if yours is
such a modem. See your modem manual for more information.
Note: Some modems, such as IBM 7857-017, are not designed for the paging func-
tion. Although they can be used for paging, they return an error message when they
do not get the expected response from another modem. Therefore, even though the
paging was successful, the error message causes the Service Processor to retry,
continuing to place pager calls for the number of retries specified in the Call-Out
Policy Setup Menu. These retries result in redundant pages.
Examples For Using the Generic Sample Modem Configuration Files
Note: ** Ring interrupt only on first ring.
Modem Setup Z Setup Z0
(Rare)
Setup F Setup F0 Setup F1
AT&T DataPort 2001 ** X
Bocamodem 1440E X
Hayes Smart Modem 300 X
IBM 5841 X
IBM 5843 X
IBM 7851 X
IBM 7852-10 X
IBM 7855 X
USRobotics
36.6K Sportster
X
Zoom V.32 X
Appendix C. Modem Configurations C-3
- User's Guide 1
- Second Edition (April 1999) 2
- Contents 3
- Communications Statements 7
- VCCI Statement 9
- Radio Protection for Germany 10
- Safety Notices 11
- Laser Safety Information 13
- Environmental Notices 15
- About This Book 17
- Trademarks 18
- Chapter 1. System Description 19
- Ergonomic Information 21
- Starting the System Unit 21
- Stopping the System Unit 23
- Using the Keyboards 25
- Using the Three-Button Mouse 27
- Handling the Mouse Correctly 28
- Caring for the Mouse 29
- Cleaning the Mouse 30
- Diskette Compatibility 31
- Write-Protect Tab 32
- Using the CD-ROM Drive 33
- Loading the CD-ROM Drive 34
- Unloading the CD-ROM Drive 34
- Cleaning the CD-ROM Drive 34
- Emergency Eject 35
- Handling Guidelines 38
- Disk Drive Status LED States 39
- SCSI Disk Drives: 39
- Privileged access password 42
- Service Processor Menus 43
- Menu Inactivity 43
- General User Menus 44
- Privileged User Menus 46
- MAIN MENU 46
- Service Processor Setup Menu 48
- Passwords 49
- System Power Control Menu 52
- System Information Menu 53
- Language Selection Menu 55
- Call-in/Call-out Setup Menu 56
- Modem Configuration Menu 56
- Serial Port Selection Menu 57
- Serial Port Speed Setup Menu 58
- Telephone Number Setup Menu 58
- Call-Out Policy Setup Menu 60
- Customer Account Setup Menu 61
- System Power-On Methods 65
- Call Out (Call-Home) 69
- Console Mirroring 70
- System Configuration: 70
- Updating Firmware from AIX 73
- MultiBoot 80
- DefaultSave 83
- Utilities 84
- Password 85
- Error Log 90
- System Firmware Recovery 97
- Display Configuration 99
- MultiBoot Menu 100
- Select Boot Devices 101
- Utilities 103
- Ethernet adapter 106
- Hard Disk Spin Up Delay 108
- System Firmware Recovery: 110
- Select Language 111
- Open Firmware Command Prompt 112
- Chapter 5. Installing Options 113
- Safety Considerations 114
- Expansion Bays 116
- Locked Position 120
- Diagnostic Sources 129
- Selecting a Console Display 129
- Undefined Terminal Types 130
- Running Online Diagnostics 130
- Refer to the following table 132
- Additional Printer Attributes 136
- Service Mode 137
- Concurrent Mode 138
- Maintenance Mode 139
- Location Codes 141
- Physical Location Codes 141
- Location Code Format 141
- AIX Location Codes 142
- P1-C1 144
- P1-M2 144
- U1-P1-M2.12 144
- Introduction to Service Aids 163
- AIX Shell Prompt Service Aid 164
- Diagnostic Task 170
- Disk Media Service Aids 170
- Disk Maintenance Service Aid 172
- Disk to Disk Copy Service Aid 172
- Optical Disk Service Aids 173
- Diskette Media Service Aid 173
- SCSI Bus Analyzer Task 179
- Service Hints Service Aid 181
- Display Firmware Device Node 182
- Display Resource Attributes 182
- SSA Location Code Format 184
- SSA Loops and Links 185
- The SSA Adapter 185
- Disk Drive Module Strings 186
- Rules for SSA Loops 187
- Loops and Data Paths 188
- SSA Service Aids 190
- The Identify Function 191
- Starting the SSA Service Aids 191
- Set Service Mode Service Aid 193
- Link Verification Service Aid 198
- Format Disk Service Aid 203
- Certify Disk Service Aid 205
- Service Aid Error Codes 207
- Microcode Maintenance 215
- Vital Product Data (VPD) 216
- Step 10 225
- Step 11 226
- Step 12 227
- Step 13 227
- Step 14 228
- Step 15 228
- Step 16 229
- Step 17 229
- Appendix A. System Records 237
- Device Records 238
- Testing the Setup 242
- Call-In: 242
- Call-Out: 243
- Serial Port Configuration 244
- Configuration File Selection 246
- Xon/Xoff Modems 249
- Ring Detection 249
- Terminal Emulators 249
- Recovery Procedures 250
- Recovery Strategy 252
- Prevention Strategy 252
- Modem Configuration Samples 253
- Sample File modem_m0.cfg 253
- Sample File modem_m1.cfg 256
- Sample File modem_z.cfg 259
- Sample File modem_z0.cfg 261
- Sample File modem_f.cfg 263
- delay 2 265
- Sample File modem_f0.cfg 266
- Sample File modem_f1.cfg 269
- # responses 271
- Pre-Standby Phase 273
- Standby Phase 274
- Bring-Up Phase 274
- Runtime Phase 275
- Numerics 277
- (continued) 278
- Index X-3 279
- Index X-5 281
- Index X-7 283
- Index X-9 285
- X-11 287
- Information Development 288
- Department H6DS-9561 288
- 11400 Burnet Road 288
- Austin, TX 78758-3493 288
- BUSINESS REPLY MAIL 288
- Part Number: 41L6147 290
- April 1999 290
- SA38-546-1 290
Relacionado con productos y manuales para Sistemas operativos IBM RS/6000
Sistemas operativos IBM H80 Manual de usuario
(230 paginas)
(230 paginas)
Magnetic-products RSDM2-04-REN-RE manuels
Manuels d'utilisation et guides de l'utilisateur pour Équipement Magnetic-products RSDM2-04-REN-RE.
Nous fournissons des manuels en pdf 1 Magnetic-products RSDM2-04-REN-RE à télécharger gratuitement par type de document : Manuel de l'utilisateur
Comentarios a estos manuales