IBM DS4700 Manual de usuario Pagina 88
- Pagina / 270
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Table 22. Description of Figure 32
Number Description
1 Enclosure ID
Fibre-channel loop and ID settings
When you install a hard disk drive in the storage subsystem, the drive tray plugs
into a printed circuit board called the midplane. The midplane sets the fibre-channel
loop ID automatically, based on the enclosure ID switch setting and the physical
location (bay) of the hard disk drive.
Working with SFPs and fiber-optic cables
Each RAID controller has up to four single-ported host channel connections
(depending on the model) and two dual-ported drive channel connections. You use
a small-form factor pluggable transceiver (SFP) to connect each host channel port
and drive channel port to hosts and storage expansion enclosures. The SFP is
inserted into the port, and then a fiber-optic cable is inserted into the SFP. The
other end of the fiber-optic cable connects to an external device. SFPs are laser
products.
Statement 3:
ds470005
1
1
1
1
Figure 32. Storage subsystem seven-segment enclosure ID on models 70 and 72
56 IBM System Storage DS4700 Express Storage Subsystem: Installation, User’s and Maintenance Guide
- GC26-7843-05 1
- Sixth Edition (November 2011) 4
- Contents 5
- Contents v 7
- Contents vii 9
- © Copyright IBM Corp. 2010 ix 11
- Figures xi 13
- © Copyright IBM Corp. 2010 xv 17
- Class 1 Laser Product 19
- Laser Klasse 1 19
- Laser Klass 1 19
- Luokan 1 Laserlaite 19
- Apparell Laser de Calsse 1À 19
- Safety xix 21
- Cable Warning: 22
- About this document 23
- About this document xxiii 25
- About this document xxv 27
- Before you call 28
- Using the documentation 28
- Finding DS4000 readme files 29
- Web sites 29
- Software service and support 30
- Hardware service and support 30
- Fire suppression systems 31
- How to send your comments 31
- Chapter 1. Introduction 33
- Operating system support 35
- Fibre channel defined 35
- SATA defined 35
- Inventory checklist 35
- Best practices guidelines 37
- Storage subsystem components 38
- Chapter 1. Introduction 7 39
- Controllers 40
- Chapter 1. Introduction 9 41
- Chapter 1. Introduction 11 43
- AC power supply and fan units 44
- Chapter 1. Introduction 13 45
- DC power supply and fan units 46
- Chapter 1. Introduction 15 47
- Battery units 49
- SFP modules 51
- Telco bezel 51
- Determining firmware levels 53
- Specifications 54
- Area requirements 54
- 77027-03 55
- Temperature and humidity 56
- 77027-02 57
- Electrical requirements 58
- Chapter 1. Introduction 27 59
- Chapter 1. Introduction 29 61
- Installation overview 63
- Serial number 64
- Machine type 64
- Model number 64
- Preparing for installation 66
- Tools and hardware required 67
- Preparing the site 67
- Preparing the rack cabinet 68
- Installing the support rails 68
- Rear of Rack 72
- Removing a controller 73
- Removing an E-DDM 77
- Front of Rack 79
- Replacing the components 80
- Replacing an E-DDM 84
- Installing a Telco bezel 85
- Enclosure ID settings 87
- Number Description 88
- 1 Enclosure ID 88
- Handling fibre-optic cables 89
- Installing SFP modules 90
- Protective cap 92
- Plastic tab 92
- SFP module 92
- Fibre-optic 95
- LC connector 97
- SC connector 97
- Redundant drive channel pair 100
- Redundant 101
- Drive Channel 101
- Recommended cabling 107
- DS4000 Storage Subsystem 127
- DS4700 Express 129
- Host 1, Host Adapter 1 and 2 138
- Host 2, Host Adapter 1 and 2 138
- Fibre channel connections 139
- Web pages 150
- Hardware responsibilities 150
- Firmware updates 156
- Checking the LEDs 157
- Front LEDs 159
- Battery unit LEDs 160
- Controller LEDs 161
- Diagnostic LED 164
- Cache memory 173
- Subsystem cache battery 174
- Replacing a controller 178
- F10ug009 179
- F10ug010 180
- Guide pin 181
- Working with hot-swap E-DDMs 183
- Table 49. Drive LED activity 184
- LED LED state Descriptions 184
- Installing hot-swap E-DDMs 185
- Figure 111. E-DDM CRU handle 186
- Replacing hot-swap E-DDMs 187
- Replacing multiple E-DDMs 188
- 77025-01 195
- Ds470011 200
- Replacing a battery unit 207
- Replacing an SFP module 209
- Replacing a midplane 210
- 810midpl 212
- General checkout 215
- Solving problems 215
- Parts listing 220
- Appendix A. Records 223
- Sample information record 225
- Installed device records 226
- Rack Mounting 228
- Template 228
- Appendix C. Power cords 231
- Appendix C. Power cords 201 233
- Appendix E. Accessibility 245
- Trademarks 247
- Important notes 248
- Particulate contamination 249
- Documentation format 249
- Notices 219 251
- Glossary 253
- Glossary 223 255
- Glossary 225 257
- Glossary 227 259
- Glossary 229 261
- Index 233 265
- Index 235 267
- Web sites (continued) 268
- SAN support xxvii 268
- Part Number: 94Y8472 270
- Printed in USA 270
- (1P) P/N: 94Y8472 270
Relacionado con productos y manuales para Barebones Servidor IBM DS4700
(187 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales